Translator

Impedance and Reactance

Impedance

Impedance, Z = V
 I
Resistance, R = V
 I
V = voltage in volts (V)
I  = current in amps (A)
Z = impedance in ohms (ohm)
R = resistance in ohms (ohm)
Impedance (symbol Z) is a measure of the overall opposition of a circuit to current, in other words: how much the circuit impedes the flow of current. It is like resistance, but it also takes into account the effects of capacitance and inductance. Impedance is measured in ohms, symbol ohm.
Impedance is more complex than resistance because the effects of capacitance and inductance vary with the frequency of the current passing through the circuit and this means impedance varies with frequency! The effect of resistance is constant regardless of frequency.
The term 'impedance' is often used (quite correctly) for simple circuits which have no capacitance or inductance - for example to refer to their 'input impedance' or 'output impedance'. This can seem confusing if you are learning electronics, but for these simple circuits you can assume that it is just another word for resistance.
Four electrical quantities determine the impedance (Z) of a circuit:
resistance (R), capacitance (C), inductance (L) and frequency (f).
Impedance can be split into two parts:
  • Resistance R (the part which is constant regardless of frequency)
  • Reactance X (the part which varies with frequency due to capacitance and inductance)
For further details please see the section on Reactance below.
impedanceThe capacitance and inductance cause a phase shift* between the current and voltage which means that the resistance and reactance cannot be simply added up to give impedance. Instead they must be added as vectors with reactance at right angles to resistance as shown in the diagram.
Phase shift means that the current and voltage are out of step with each other. Think of charging a capacitor. When the voltage across the capacitor is zero, the current is at a maximum; when the capacitor has charged and the voltage is at a maximum, the current is at a minimum. The charging and discharging occur continually with AC and the current reaches its maximum shortly before the voltage reaches its maximum: so we say the current leads the voltage. 

Reactance, X

Reactance (symbol X) is a measure of the opposition of capacitance and inductance to current. Reactance varies with the frequency of the electrical signal. Reactance is measured in ohms, symbol ohm.
There are two types of reactance: capacitive reactance (Xc) and inductive reactance (XL).
The total reactance (X) is the difference between the two:    X = XL - Xc
  • Capacitive reactance, Xc
      Xc =     1     where:  Xc = reactance in ohms (ohm)
    f    = frequency in hertz (Hz)
    C   = capacitance in farads (F)  
    2pifC

    Xc is large at low frequencies and small at high frequencies.
    For steady DC which is zero frequency, Xc is infinite (total opposition),
    hence the rule that capacitors pass AC but block DC.For example: a 1µF capacitor has a reactance of 3.2kohm for a 50Hz signal,
    but when the frequency is higher at 10kHz its reactance is only 16ohm.
  • Inductive reactance, XL
      XL = 2pifL  where:  XL = reactance in ohms (ohm)
    f    = frequency in hertz (Hz)
    L   = inductance in henrys (H)  

    XL is small at low frequencies and large at high frequencies.
    For steady DC (frequency zero), XL is zero (no opposition),
    hence the rule that inductors pass DC but block high frequency AC.For example: a 1mH inductor has a reactance of only 0.3ohm for a 50Hz signal,
    but when the frequency is higher at 10kHz its reactance is 63ohm.

Input Impedance ZIN

input impedanceInput impedance (ZIN) is the impedance 'seen' by anything connected to the input of a circuit or device (such as an amplifer). It is the combined effect of all the resistance, capacitance and inductance connected to the input inside the circuit or device.
It is normal to use the term 'input impedance' even for simple cases where there is only resistance and the term 'input resistance' could be used instead. In fact it is usually reasonable to assume that an input impedance is just resistance providing the input signal has a low frequency (less than 1kHz say).
The effects of capacitance and inductance vary with frequency, so if these are present the input impedance will vary with frequency. The effects of capacitance and inductance are generally most significant at high frequencies.
Usually input impedances should be high, at least ten times the output impedance of the circuit (or component) supplying a signal to the input. This ensures that the input will not 'overload' the source of the signal and reduce the strength (voltage) of the signal by a substantial amount. 

Output Impedance ZOUT

output impedance
The equivalent circuit of any output
The output of any circuit or device is equivalent to an output impedance (ZOUT) in series with a perfect voltage source (VSOURCE). This is called the equivalent circuit and it repesents the combined effect of all the voltage sources, resistance, capacitance and inductance connected to the output inside the circuit or device. Note that VSOURCE is usually not the same as the supply voltage Vs.
It is normal to use the term 'output impedance' even for simple cases where there is only resistance and the term 'output resistance' could be used instead. In fact it is usually reasonable to assume that an output impedance is just resistance providing the output signal has a low frequency (less than 1kHz say).
The effects of capacitance and inductance vary with frequency, so if these are present the output impedance will vary with frequency. The effects of capacitance and inductance are generally most significant at high frequencies.

Usually output impedances should be low, less than a tenth of the load impedance connected to the output. If an output impedance is too high it will be unable to supply a sufficiently strong signal to the load because most of the signal's voltage will be 'lost' inside the circuit driving current through the output impedance ZOUT. The load could be a single component or the input impedance of another circuit.
output impedance and load
The load can be a single component or
the input impedance of another circuit

  • Low output impedance, ZOUT << ZLOAD
    Most of VSOURCE appears across the load, very little voltage is 'lost' driving the output current through the output impedance. Usually this is the best arrangement.
  • Matched impedances, ZOUT = ZLOAD
    Half of VSOURCE appears across the load, the other half is 'lost' driving the output current through the output impedance. This arrangement is useful in some situations (such as an amplifier driving a loudspeaker) because it delivers maximum power to the load. Note that an equal amount of power is wasted driving the output current through ZOUT, an efficiency of 50%.
  • High output impedance, ZOUT >> ZLOAD
    Only a small portion of appears across the load, most is 'lost' driving the output current through the output impedance. This arrangement is unsatisfactory.


The output resistance of a voltage divider

voltage divider circuit
Voltage divider
voltage divider output impedance
Equivalent circuit of a voltage divider
voltage divider with an LDR at bottom
Voltage divider with an LDR
Voltage dividers are widely used in electronics, for example to connect an input transducer such as an LDR to a circuit input.
For successful use the output impedance of the voltage divider should be much smaller than the input impedance of the circuit it is connected to. Ideally the output impedance should be less than a tenth of the input impedance.
In the equivalent circuit of a voltage divider the output impedance is just a resistance and the term 'output resistance' could be used. ROUT is equal to the two resistances (R1 and R2) connected in parallel:
  Output impedance,  ROUT = R1 × R2 
 R1 + R2

The voltage source VSOURCE in the equivalent circuit is the value of the output voltage Vo when there is nothing connected to the output (and therefore no output current). It is sometimes called the 'open circuit' voltage.
  Voltage source,  VSOURCE =  Vs × R2 
 R1 + R2

In most voltage dividers one of the resistors will be an input transducer such as an LDR. The transducer's resistance varies and this will make both VSOURCE and ROUTvary too. To check that ROUT is sufficiently low you should work out its highest value which will occur when the transducer has its maximum resistance (this applies wherever the transducer is connected in the voltage divider).
For example: If R1 = 10kohm and R2 is an LDR with maximum resistance 1Mohm, ROUT = 10k × 1M / (10k + 1M) = 9.9kohm (say 10kohm). This means it should be connected to a load or input resistance of at least 100kohm

2 comments:

  1. It is a wonderful information and also get good knowledge and ideas from this article. The author is giving good thoughts and suggestions to each and every readers through this article.The good advantages of this article is giving good thought to each and every readers and also it’s giving good impressions. Looking forward to another article.
    www.iasosource.com | www.emblemzone.com

    ReplyDelete